| 1. | Two kinds of normal force of permanent magnet linear motor were fully analyzed by using finite element analysis ( fea )
摘要采用有限元仿真的方法，建立了永磁直线电机的模型，对初级与次级、次级与机床间的两种法向吸力进行了详细分析。 |
| 2. | In this thesis the generation of orthogonal - aligned - shaft face gear , finite element analysis ( fea ) of the bend stress and contact stress of the fg drive are studied
本文主要研究了正交面齿轮的齿面生成、正交面齿轮传动的弯曲应力和接触应力的有限元分析。 |
| 3. | This paper adopts finite element analysis ( fea ) and experimental modal analysis ( ema ) to obtain the equivalent mathematical model of a frp golf shaft , respectively
摘要本文结合有限元素分析与实验模态分析以求得碳纤维高尔夫球杆之等效?学模型，并探讨其机械性质。 |
| 4. | Thirdly , the bearing and deformation characteristics of single and group piles are investigated by means of axisymmetric finite element analysis ( fea ) and three - dimensional fea
再次，运用二维轴对称有限元法以及三维有限元法，系统分析了挤扩支盘桩单桩和群桩的承载变形性状。 |
| 5. | Since some experiments cost not only lots of money , but also people resource and time , the finite element analysis ( fea ) of rc structures is becoming increasingly important
而某些试验研究不但非常昂贵，还需要耗费大量的人力、时间，因此钢筋混凝土结构非线性有限元分析正突显出日益重要的作用。 |
| 6. | The method of surface reconstruction based on finite element analysis ( fea ) is produced in research of interpolatory subdivision surface , and algorithm is designed according to the method of surface reconstruction
在对曲面插值细分的研究中，论文提出了基于有限元分析的离散数据点的曲面重构方法。 |
| 7. | This thesis is an explore to the immature theories through elasto - plastic finite element analysis ( fea ) . to demonstrate the feasibility of fea used in masonry homogenization , the following tests are conducted : 1
针对这个事实，本文采用了弹塑性有限元模拟的方法，探索了一下该方法应用于砌体均质化理论的可行性。 |
| 8. | Though cae has very strong function in finite element analysis ( fea ) , it has so many difficulties in modeling that the time spent on modeling almost occupy a half of the one of whole analysis process
Cae有强大的有限元分析功能，但是在创建几何模型方面功能很弱，分析师用于几何建模的时间几乎占整个分析过程的一半。 |
| 9. | Taken the stiffnesses as the goal of optimization , the parameters of the flexure hinges are optimized with the methods of theoretical calculation and the finite element analysis ( fea ) respectively
基于结构力学理论,推导出二维微动平台和支杆柔性铰链刚度计算表达式。分别通过理论计算和有限元分析的方法来设计柔性铰链的参数。 |
| 10. | The research of the bend stress of fg drive is made by the use of finite element analysis ( fea ) . the influence of the force location on the calculating stress of the bend strength is considered
在面齿轮传动的弯曲应力的研究中,利用有限元分析法对面齿轮的弯曲应力作了分析;考虑了力的作用点对弯曲应力的影响;获得了弯曲应力的分布规律。 |
